![]() |
|
|
|
#1
|
|||
|
|||
Looking for tools not yet in the list
Does anyone near Norfolk VA have a timing chain crimping tool for a 240D to rent or sell?
chonahe@live.com Hello I need to rent a ball joint press for a 560 SEL or does anyone no a shop here on long island that would press them in for me I saw that Billybob has a ball joint press for rent for a 560sel but I can not send him an email for some reason Hi I need to change the front shocks on my 1989 300E (W124)? Can anybody rent me the coil spring compression tool - I live in DC Metgro area/MD. Anyone have a w201/w124 ball joint press I can borrow or rent? I live in the Atlanta area! Thanks in Advance! ------------dirtyhands Anyone have the valve spring compressor for the valve stem seals? Need it for a 420 (m116)... I'm looking to replace all four rear subframe bushings on a '94 w124 (e420) in the near future and was wondering if anyone has the bushing R&R tools. The part numbers for these tools are 201 589 10 43 00 201 589 11 43 00 I'm not sure how necessary these are for the job, but I'd rather not spend a day sweating these guys in and and out (any experience would be appreciated!). Thanks -- Greg Last edited by vstech; 04-04-2011 at 09:39 AM. |
#2
|
|||
|
|||
Lower Control Arm Bushings
Hi,
Will somebody suggest a tool to remove and install LCA Bushings on a 98 e320 (w210) I will rent or buy. |
#3
|
|||
|
|||
I am looking to see if someone has an internal spring compressor that I can borrow, rent, or maybe buy. I am located in Milpitas, CA. 45-min south of San Francisco.
I have a 2000 E320 Wagon Email me at surakung@gmail.com if you do. Thanks~ (pictured below) |
#4
|
|||
|
|||
Valve Adjusment tools and/or compression test!
By any chance does any one have the tools needed for a valve adjustment and compression test? I mainly need the valve adjustment tools.
I have plenty of feed back on other sites and I only need them for one weekend. I will pay shipping both ways and maybe a small fee if needed ![]() I am new to diesels and also a senior in high school and at the moment I cant afford a set for my self, or else I would and keep them for future use! I am in Danville, California.. Thanks very much! Andrew andrewtexas123@hotmail.com |
#5
|
|||
|
|||
I'm interested in renting the following tools.....
I want to replace the injector nozzles in my 617 engine and remove the prechambers soz I can replace the seal. I've been getting some leaking in those areas and I feel it's time to see what she'll feel like with new injector nozzles.
Here are the tools I'd like to rent: 34) Prechamber ring wrench, pin type, 60X, 61X....Billybob............................$15 37) Prechamber removal tool, screw press, 61X.....Billybob............................$25. 20) Injector pop tester........................................Grezer...........................$20. If these tools are still available let me know. I'd like to handle these transactions via money orders and mail. I have a 1982 300sd with 350k on the clock. She runs well but always needs more attention than I'm able to give her. ![]() Thanks Allen |
#6
|
|||
|
|||
IP Delivery Valve Splien Scoket 87 300D
Looking to rent a spline socket for the delivery value removal off the injector pump of a 1987 300D
MB part number 617 589 01 09 00 Dealer cost $58. |
#7
|
|||
|
|||
Looking for tools in all the wrong places ...
I'm looking to replace all four rear subframe bushings on a '94 w124 (e420) in the near future and was wondering if anyone has the bushing R&R tools. The part numbers for these tools are
201 589 10 43 00 201 589 11 43 00 I'm not sure how necessary these are for the job, but I'd rather not spend a day sweating these guys in and and out (any experience would be appreciated!). Thanks -- Greg
__________________
Greg Stein '94 E420 '86 420 SEL '79 300 TD |
#8
|
|||
|
|||
Quote:
I personally dont stipulate the OEM part, the B201-1143 is prefectly fine with me... |
#9
|
|||
|
|||
CIS-E Fuel Pressure Tester
Would like to rent or possibly buy a CIS-E Fuel Pressure Tester. If anyone has one to rent I would appreciate it.
Thanks, Rebe Email at bikerman@swbell.net |
#10
|
|||
|
|||
Looking for a modified flare nut wrench for oil cooler lines on a 1985 300td. It's the modified 1 and 1/16 box end wrench.
__________________
2009 E320 Bluetec 117,000 1995 E300D 306,000 Sold 1996 Ford Taurus LX 130,000 Sold 1985 300TD Still 225,000 Sold 2016 Ford Fusion 24,900 |
#11
|
|||
|
|||
anyone have a set of valve wrenches to rent? nobody in the master thread is reachable, and i need to do the job.
![]()
__________________
'81 240D 4 speed '97 E420 |
#12
|
|||
|
|||
Quote:
__________________
http://i193.photobucket.com/albums/z...-RESIZED-1.jpg 1991 300E - 212K and rising fast... |
#13
|
||||
|
||||
I'll need a front wheel hub puller, MB tool #116 589 33 00.
This is for a 1984 300 CD.
__________________
83 SD 84 CD |
#14
|
||||
|
||||
Yes, if you still need them.
__________________
83 SD 84 CD |
#15
|
||||
|
||||
I was successful using a "rental" from the local AutoZoo, so I no longer need this.
__________________
83 SD 84 CD |
![]() |
Bookmarks |
|
|